Rokasgrāmata Powerworks PD60PS Ķēdes zāģis

Rokasgrāmata

English (original instructions)

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

 Place the bar onto the bar stud so that the chain

tensioning pin fits into the chain tensioning pin hole.

 Fit the chain over the sprocket and into the bar

groove. The cutters on the top of the bar should face

toward the bar tip, in the direction of the chain rotation.

 Replace the drivecase cover and install the lock knob.

Tighten the lock knob finger tight only. The bar must

be free to move for tension adjustment.

 Remove all slack from chain by turning the chain

tensioning screw clockwise, assuring that the chain

seats into the bar groove during tensioning.

 Lift the tip of the bar up to check for sag. Release the

tip of the bar, and turn the chain tensioning screw 1/2

turn clockwise. Repeat this process until sag does not

exist.

 Hold the lip of the bar up and tighten the lock knob

securely.

 Chain is correctly tensioned when there is no slack on

the underside of the bar, the chain is snug, but it can

be turned by hand without binding.

ADJUSTING THE CHAIN TENSION

See Figure 13-16

 Loosen the chain cover lock nuts with the supplied

wrench. The chain cover lock nuts do not have to

be completely removed in order to adjust the chain

tension.

 Rotate the chain adjustment screw clockwise

to increase the chain tension and rotate

counterclockwise to decrease the chain tension.

 Once the chain is at the desired tension, tighten the

chain cover lock nuts.

WARNING

Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the bar and

chain.

WARNING

When the saw chain is new, check the tension

frequently during the rst two hours of use as a new

saw chain stretches slightly.

CHAIN MAINTENANCE See Figure 17

For smooth and fast cutting, the chain needs to be

maintained properly. The following conditions indicate

that the chain requires sharpening:

 Wood chips are small and powdery.

 Chain must be forced through the wood during cutting.

 Chain cuts to one side.

During maintenance of the chain, consider the following:

 Improper filling angle of the side plate can increase

the risk of severe kickback.

 Depth gauge (or raker clearance) setting determines

the height the cutter enters the wood and the size of

the wood chip that is removed. Too much clearance

increases the potential for kickback. Too little

clearance decreases the size of the wood chip thus

decreasing the chain's cutting ability.

 If the cutter teeth hit hard objects such as nails or

stones, or are abraded by mud or sand on the wood,

have an authorized service center sharpen the chain.

NOTE:if there’re any cracks on chain pitch or guide

bar,stop to use the tool at once and replace the damaged

parts. Refer to Replacing The Bar And Chain.

HOW TO SHARPEN THE CUTTERS

See Figure 18-21

Be careful to file all cutters to the specified angles and to

the same length, as fast cutting can be obtained only when

all cutters are uniform.

 Tighten the chain tension enough that the chain does

not wobble. Do all of your filling at the mid-point of the

bar. Wear gloves for protection.

 Use a 5/32 in. diameter round file and holder.

 Keep the file level with the top plate of the tooth. Do

not let the file dip or rock.

 Using light but firm pressure, stroke towards the front

corner of the tooth. Lift file away from the steel on

each return stroke.

 Put a few firm strokes on every tooth. File all left hand

cutters in one direction. Then move to the other side

and file the right hand cutters in the opposite direction.

Occasionally remove filings from the file with a wire

brush.

WARNING

Dull or improperly sharpened chain can cause

excessive motor speed during cutting which may result

in severe motor damage.

WARNING

Improper chain sharpening increases the potential of

kickback. Failure to replace or repair damaged chain

can cause serious injury.

STORAGE

STORING THE PRODUCT

 Clean all foreign material from the product. Store

idle unit indoors in a dry, well-ventilated area that is

inaccessible to children. Keep away from corrosive

4

Vērtējums

Vairāk par šo rokasgrāmatu

Mēs saprotam, ka ir patīkami, ka jūsu Powerworks PD60PS Ķēdes zāģis ir papīra rokasgrāmata. Jūs vienmēr varat lejupielādēt rokasgrāmatu no mūsu vietnes un pats to izdrukāt. Ja vēlaties saņemt oriģinālo rokasgrāmatu, iesakām sazināties ar Powerworks. Viņi varētu nodrošināt oriģinālu rokasgrāmatu. Vai meklējat sava Powerworks PD60PS Ķēdes zāģis rokasgrāmatu citā valodā? Izvēlieties vēlamo valodu mūsu mājaslapā un meklējiet modeļa numuru, lai redzētu, vai tas ir pieejams.

Specifikācijas

Visas rokasgrāmatas par Powerworks Ķēdes zāģi
Citas Ķēdes zāģi rokasgrāmatas

Bieži uzdotie jautājumi par Powerworks PD60PS Ķēdes zāģis

Mūsu atbalsta komanda meklē noderīgu informāciju par produktu un atbild uz bieži uzdotajiem jautājumiem. Ja atrodat ko nepareizu bieži uzdotajos jautājumos, informējiet mūs, izmantojot saziņas veidlapu.

Saistītie produkti

Rokasgrāmata

Powerworks PD60CS40 Ķēdes zāģis

Rokasgrāmata

AL-KO EKS 2000/35 Ķēdes zāģis

Rokasgrāmata

Dedra DED7099 Ķēdes zāģis

Rokasgrāmata

EGO CSX3002 Ķēdes zāģis

Rokasgrāmata

Stiga CS 48 Li 14 Ķēdes zāģis

Rokasgrāmata

Skil 0650 CA Ķēdes zāģis

Rokasgrāmata

Skil 0512 AA Ķēdes zāģis

Rokasgrāmata

EGO CS1410E Ķēdes zāģis

Saistītās kategorijas