Rokasgrāmata Tryton TDW1050 Triecienurbis

Rokasgrāmata

n Controlling the speed

remove the dust obstructing motor cooling air supply.

By increasing or decreasing the pressure on switch (6) the user can

TRANSPORTATION:

control the rotational speed steplessly.

The drill should be transported and stored in a box providing protection

Low pressure on the switch (6) results in low speed. Increasing the

against humidity, dust and tiny objects penetration; special care should

pressure raises the speed.

be taken to protect ventilation inlets. Small objects that get into the

n Setting the speed

device can damage the motor.

Using rotational speed control (5) the user can set a desired speed. It can

TROUBLESHOOTING GUIDE (TYPICAL PROBLEMS):

be done during operation.

The drill does not work:

Speed depends on the material drilled and working conditions and can

- check whether the power cord is properly connected and check fuses.

be determined by performing a test.

The drill works with interruptions or generates sparks:

CHANGING THE DRILL CHUCK :

- check and replace carbon brushes.

Prior to any work on the power tool unplug it from

NOTE! Carbon brushes can be replaced only by competent electricians.

the mains socket.

- If the power tool does not work despite being supplied from a proper

power source, have the tool repaired sending it to the service center. The

The chuck installed on a right-hand/ left-hand rotating drill is fixed with

addresses are provided in the warranty card.

a left-hand thread bolt. Prior to changing the drill chuck, undo the screw

using a Phillips type (Ph2) screwdriver inserting it from the front through

the chuck opening.

A left-hand thread screw can be undone only by turning it

clockwise.

To remove the chuck (1) put the drill on a stable surface, e.g. on a work

bench, apply a two-hole spanner (17 mm) to notches at the spindle. Hold

NOTE:

the chuck with one hand and turn the spanner counterclockwise with the

other until the chuck is completely removed (see Fig. C).

The drill chuck installation should be carried out in the opposite order.

No dirt is allowed on the chuck seat and spindle thread.

TIPS REGARDING OPERATION:

ź After a longer operation at low speeds run the power tool at its

maximum speed with no load for about 3 minutes to cool it down.

ź To drill holes in ceramic tiles set the operation mode switch (2) to

position «drill». Once the hole in the ceramic tile is ready, set the

operation mode switch to position «impact drill» and continue

drilling in this mode.

ź When drilling in concrete, stone or walls hard alloy drill bits should be

used.

ź When drilling in metal use sharp metal drill bits only.

NOTE: Proper drill bit selection reduces vibrations during drilling, which

increases drilling efficiency considerably.

ź When tightening/undoing screws place the bit onto the screw/nut

when the chuck is stopped.

STORAGE AND MAINTENANCE:

Generally, this power tool does not require any special maintenance.

Store the machine in a place away from children, keep it clean and

protect from humidity and dust. Storage conditions should exclude any

mechanical damage and weathering.

After drilling in concrete, in intensely dusty environments it is

recommended to remove dust from ventilation openings and the drill

chuck with a stream of compressed air. It will protect bearings and

MANUFACTURER:

PROFIX Ltd.,

34 Marywilska Street,

03-228 Warsaw, POLAND.

PROTECTION OF THE ENVIRONMENT:

The symbol nearby denotes that old equipment must

never be thrown away together with other waste (with the

penalty of a fine). Hazardous components of electronic

equipment may adversely affect the natural environment and

human health.

Each household may contribute to the recovery and reuse (recycling) of

old machinery and equipment. Both in Poland and Europe a system for

recovery of used equipment either exists or is being created. The system

obliges all organizations that sell such equipment to collect the used

machinery and appliances. Moreover, general purpose collecting points

for such equipment are available.

PICTOGRAMS:

Explanation of the icons located on the nominal plate and the

information tags.

6

«Always wear safety goggles»

«Wear »hearing protection

«Wear a dust mask»

«Read this instruction before switching on the

power supply and starting the work»

The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the company

reserves the right to make amendments to the product specification without a prior notice. The images included into the

operation manual are only of the exemplary nature and may slightly differ from actual appearance of the device purchased.

Vērtējums

Vairāk par šo rokasgrāmatu

Mēs saprotam, ka ir patīkami, ka jūsu Tryton TDW1050 Triecienurbis ir papīra rokasgrāmata. Jūs vienmēr varat lejupielādēt rokasgrāmatu no mūsu vietnes un pats to izdrukāt. Ja vēlaties saņemt oriģinālo rokasgrāmatu, iesakām sazināties ar Tryton. Viņi varētu nodrošināt oriģinālu rokasgrāmatu. Vai meklējat sava Tryton TDW1050 Triecienurbis rokasgrāmatu citā valodā? Izvēlieties vēlamo valodu mūsu mājaslapā un meklējiet modeļa numuru, lai redzētu, vai tas ir pieejams.

Specifikācijas

Visas rokasgrāmatas par Tryton Triecienurbji
Citas Triecienurbji rokasgrāmatas

Bieži uzdotie jautājumi par Tryton TDW1050 Triecienurbis

Mūsu atbalsta komanda meklē noderīgu informāciju par produktu un atbild uz bieži uzdotajiem jautājumiem. Ja atrodat ko nepareizu bieži uzdotajos jautājumos, informējiet mūs, izmantojot saziņas veidlapu.

Saistītie produkti

Rokasgrāmata

Tryton TDW1200 Triecienurbis

Rokasgrāmata

Tryton TDW1050K Triecienurbis

Rokasgrāmata

Tryton TDW550 Triecienurbis

Rokasgrāmata

Tryton TDW710 Triecienurbis

Rokasgrāmata

Tryton TDW850K Triecienurbis

Rokasgrāmata

Tryton TDW1200 K Triecienurbis

Rokasgrāmata

Bosch GBM 32-4 Triecienurbis

Rokasgrāmata

Bosch GSB 19-2 RE Professional Triecienurbis

Saistītās kategorijas