Rokasgrāmata FERM TSM1036 Galda zāģis
Nepieciešama rokasgrāmata savam FERM TSM1036 Galda zāģis? Zemāk var apskatīt un bez maksas lejupielādēt PDF rokasgrāmatu latviešu valodā. Šim produktam pašlaik ir 0 bieži uzdotie jautājumi, 1 komentārs un 1 balss ar vidējo produkta vērtējumu 0/100. Ja šī nav jūsu vēlamā rokasgrāmata, lūdzu, sazinieties ar mums.
Vai jūsu produkts ir bojāts, un rokasgrāmatā nav sniegts risinājums? Dodieties uz Repair Café, lai veiktu bezmaksas remontu.
Rokasgrāmata
7
EN
bottom of the bench saw machine and electric
motor for a longer machine life. Dust piles must
be removed.
10. Always lock the different degree set-ups before
you start processing.
11. Only buy suitable saw blades with a number
of revolutions of at least 6000 revolutions per
minute.
12. Only use the correct saw blade. Too small or too
big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the flanges
before you assemble the new blade. Then
assemble the blade in the correct direction and
pull the flanges firmly using the central bolt.
15. Only use original flanges. All other types are not
suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must also
remain assembled.
18. Never grease the saw blade while it is rotating.
19. Always keep your hands removed from the track
of the saw blades.
20. Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21. Ensure that the workpiece never touches
the saw blade before the machine has been
switched on.
22. Never process metal or stone sorts with this
machine.
23. Use support aids in order to support long
workpieces.
24. Never use the machine in a dangerous
environment, where inflammable gases or fluids
are present.
25. Never leave the machine unattended without
first disconnecting it from the mains voltage.
26. If you hear abnormal noises, try to trace them or
take the machine to a recognized fitter, or repair
company.
27. If a part is broken or damaged, replace it or
repair it immediately.
28. Never stand in the track of the saw blade but
stand to the left or the right of the saw bench.
29. Your hands must likewise be placed next to the
track of the saw blade.
30. Always use the push stick instead of your hands
to push the wood through the saw.
31. Always place the wood at the front of the saw
bench and then push it further back.
32. For mitring only the adjustable guide must be
used and the fence must be removed.
33. Never use the fence as a linear measure for
cutting off beams.
34. If the saw blade is locked: first switch off the
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Always use sharp saw blades.
• Do not saw too small workpieces.
• Never release the workpiece before it has
been completely pushed through the saw.
• Always adjust the guide parallel to the saw
blade.
• Never remove the saw protection.
36. Before you continue sawing, ensure that you are
standing firmly and that your hands are in the
required position.
37. Never use thinners to clean the machine. Only
use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or
deformed.
39. Replace table insert when worn.
40.
Only use saw blades specified by the
manufacturer that are intended for working with
wood or similar materials according to EN847-1.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect tabelsaws to a dust-collecting device
when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45. Take care when slotting.
Make sure, when changing the saw blade, the
blade width is not smaller and the main blade
thickness of the saw blade is not greater than the
thickness of the riving knife.
Wear personal protective equipment, these could
include:
• Hearing protection to reduce the risk of hearing
loss
• Eye protection
• Inhale respiratory protection to reduce the risk of
harmful dust
• Gloves when handling the blades and rough
materials (recommendation, saw blades, are
whenever practicable, carried in a container)
Vērtējums
Paziņojiet mums, ko jūs domājat par FERM TSM1036 Galda zāģis, novērtējot produktu. Vai vēlaties dalīties pieredzē ar šo produktu vai uzdot jautājumu? Ievadiet savu komentāru lapas apakšdaļā.Vairāk par šo rokasgrāmatu
Mēs saprotam, ka ir patīkami, ka jūsu FERM TSM1036 Galda zāģis ir papīra rokasgrāmata. Jūs vienmēr varat lejupielādēt rokasgrāmatu no mūsu vietnes un pats to izdrukāt. Ja vēlaties saņemt oriģinālo rokasgrāmatu, iesakām sazināties ar FERM. Viņi varētu nodrošināt oriģinālu rokasgrāmatu. Vai meklējat sava FERM TSM1036 Galda zāģis rokasgrāmatu citā valodā? Izvēlieties vēlamo valodu mūsu mājaslapā un meklējiet modeļa numuru, lai redzētu, vai tas ir pieejams.
Specifikācijas
| Zīmols | FERM |
| Modelis | TSM1036 |
| Kategorija | Galda zāģi |
| Faila veids | |
| Faila lielums | 12.77 MB |
Visas rokasgrāmatas par FERM Galda zāģi
Citas Galda zāģi rokasgrāmatas
Pievienoties sarunai par šo produktu
Šeit varat dalīties savās domās par FERM TSM1036 Galda zāģis. Ja jums ir jautājumi, vispirms rūpīgi izlasiet rokasgrāmatu. Rokasgrāmatu var pieprasīt, izmantojot mūsu saziņas veidlapu.
atbildēt | Tas bija noderīgi (0) (Tulkojis Google)