
EN
• If the device also supports Audio Video Remote Control Prole
(AVRCP), you can use the soundbar's remote control to play music
stored on the device.
1. Pair your device with the soundbar.
2. Play music via your device (if the Bluetooth device supports A2DP).
3. Use the soundbars remote control to control playback with the
and the
/ (if the Bluetooth device supports AVRCP).
NOTES:
ū The operational range between this soundbar and a Bluetooth device
is approximately 8 meters (without any object between the Bluetooth
device and the soundbar).
ū Compatibility with all Bluetooth devices is not guaranteed.
ū Any obstacle between this soundbar and a Bluetooth device can reduce
the operational range.
ū If the signal strength is weak, your Bluetooth receiver may disconnect, but
it will re-enter pairing mode automatically.
USB operation
1. Insert the USB device into the soundbar's USB socket.
2. Press the
button repeatedly on the soundbar or the remote
control to select the USB source.
3. You can navigate dierent folders stored on the USB device. Press
/
to change the folder.
4. Press
to play the selected track.
5. During playback:
ū To pause or resume play, press the
button on the remote
control.
ū To skip to the previous/next le, press the
/ buttons on the
remote control. Press and hold
/ to fast rewind / fast forward
a track.
TIPS:
ū USB devices up to 32GB are supported.
ū Only MP3/OGG/WAV/FLAC/AAC/AAC+/ALAC les can be played back.
The USB port is for playback or upgrading the software of the soundbar.
It is not for charging purposes.
Menu operation
Navigate the soundbars menu by using the remote control and pressing
. Use the directional control on the remote control to navigate the
available options. Press
to select the menu option. To select a setting
within a menu option, use
/ . Press to enter a sub-menu. Press
to return to the menu level above.
SURR
Turns Dolby Virtualiser or DTS Virtual:X ON or OFF. Dolby Virtualiser
aects Dolby Signals. DTS Virtual:X aects DTS and PCM signals.
NOTE:
ū SURR ON/OFF has no eect on a Dolby Atmos signal.
AUDIO FORMAT (scrolling)
Displays on the current audio format being played.
SUBVOL
Adjust the output volume of the subwoofer. Choose between VOL +5
and VOL -5.
SPKVOL
Opens the rear surround speaker volume sub menu.
SPK L or SPK R. Adjust the volume of each surround speaker.
Choose between VOL +5 and VOL -5.
MUTE. Change this setting to mute the rear speakers. Options are ON
or OFF.
NOTE:
ū The default setting is OFF. If switched ON, the rear surround speakers
will remain muted until they are unmuted, even if the system has been
in standby. Unplugging the soundbar from the mains power supply will
automatically switch muting OFF again.
DISP
You can change how many seconds elapse before the soundbars display
turns o.
Choose from: 5, 10 or ON. ON will keep the display active at all times.
DIM
You can change the brightness level of the soundbars display.
Choose from: LOW, MED, or HIGH.
STDBY
Change this setting to turn o the automatic standby option. Options
are ON or OFF.
The default is ON.
WLPAIR
Select this to manually pair the subwoofer and (optional) rear surround
speakers.
WL VER
Shows the current wireless subwoofer and rear surround speakers
software version.
SW VER
Shows the current software version of the soundbar.
SW UPG
Activates a software upgrade from an inserted USB stick.
NOTE:
ū This will only work with compatible software on a USB stick inserted into
the soundbars USB port. Periodically check www.sharpconsumer.com for
software updates.
RESET
Opens the reset sub menu.
Choose <Yes> to reset the soundbar. Choose <No> to exit or press the
button.
Room calibration and positional
adjustment
The volume of the subwoofer (and rear speakers if purchased
separately) can be adjusted relative to the soundbar. This manual
calibration allows for greater exibility when positioning the system
components in the room. The default volume for each component is set
to 0 and can be adjusted from -5 to +5. Based on the listening position,
the default volumes assume a distance of 2m from the subwoofer and
1.5m from the rear speakers. Use the <SUBVOL> or <SPKVOL> options
in the menu to balance the system to your preference. Once set, the
component volume will adjust with the soundbar volume to maintain
the system balance.
Troubleshooting
Q: Sometimes I notice minor distortions in voices played through the
rear surround speakers (available to purchase separately).
A: This should only occur when a 2.0 channel stereo audio source
is being upmixed to 5.1.4 or 7.1.4 channels. With 2.0 channel audio
formats, vocals are generally intended to be played from the soundbar
only (this is not always the case with multi-channel audio sources).
However, in some circumstances voices from 2.0 channel audio sources
cannot be separated reliably by the Dolby and DTS upmixer; the
result may be that you notice some voices are played through the rear
surround speakers at a low volume, and in some instances these voices
Pievienoties sarunai par šo produktu
Šeit varat dalīties savās domās par Sharp HT-SBW53121(SL) Mājas kinozāles sistēma. Ja jums ir jautājumi, vispirms rūpīgi izlasiet rokasgrāmatu. Rokasgrāmatu var pieprasīt, izmantojot mūsu saziņas veidlapu.